This circuit component models a microstrip rectangular inductor without bridge at internal port 2. You can implement any model of bridge to attach port 2 to an external circuit. MRINDNBR is based on evaluation of self- and mutual-inductances, capacitances, and resistances between all parallel segments, which is based on an accurate quasi-static model of an arbitrary number of edge-coupled microstrip lines.
|NS||Number of linear segments (>=4)||15|
|L1||Length of first segment||Length||80 um|
|L2||Length of second segment||Length||155 um|
|L3||Length of third segment||Length||165 um|
|LN||Length of last segment||Length||35 um|
|W||Conductor width||Length||10 um|
|S||Conductor spacing||Length||5 um|
NS. The number of linear conductor segments forming the inductor. NS should be greater than 4 and less than NSMAX. The value of NSMAX can be evaluated from the condition LNMAX >0, where
LNMAX = L2-(NS-2)(W+S)/2 for even NS
LNMAX = L3-(NS-3)(W+S)/2 for odd NS
The layout feasibility check is run before performing calculations.
LN. The length of the last segment LN should not exceed LNMAX (see previous). If you define too large a value of LN, the model automatically sets LN to LNMAX and issues a warning. LN also should not be less than W/2. If you define too small a value of LN, the model automatically sets LN to W/2 and issues a warning.
In90deg, Out90deg. (Layout cell): Note that the corresponding layout cell of this model has parameters In90deg, Out90deg (to edit values of these parameters, select the corresponding layout cell, right-click and choose ). On the Parameters tab of the dialog box that displays, setting these parameters to nonzero values means that the location of faces at the junction either at port 1 (In90deg) or at port 2 (Out90deg) provides connection to an external circuit via right (90deg) bend. Correspondingly, setting these parameters to zero means that the location of the face at the corresponding junction provides an "in line" connection to an external circuit. The default values are zeros. Setting to nonzero values (for example, to 1) does not affect electrical properties of the model. No bend component is added automatically and you must attach the model of bend to the corresponding port at schematics.
NS should be greater than 4 and less than NSMAX. The value of NSMAX can be evaluated from the condition LNMAX >0 (see previous).
To decrease the calculation time for schematics that contain several MRINDNBR inductors, cache is implemented for this model. This means that during the first evaluation of a schematic the most time-consuming intermediate parameters for each inductor instance are being stored in memory cache. Each inductor model checks this cache looking for its duplicate. Duplicate inductors copy the appropriate parameters from memory cache, saving substantially on their recalculation.
Note that the model caches only frequency-independent characteristics of coupled lines, but recalculates the large equivalent circuit network (derived from coupled line characteristics) at each swept frequency. Thus, if the number of swept frequency points is large (say, 300) the total time spent on equivalent circuit evaluation may substantially exceed the time for evaluation of coupled line characteristics. In this particular case, time saving due to caching may be relatively moderate.
NOTE: The implementation of EM Quasi-Static models relies heavily on the involved numerical algorithms. This may lead to a noticeable increase in simulation time for schematics that employ many such models.
This element uses line types to determine its layout. By default, the layout uses the first line type defined in your Layout Process File (LPF). You can change the element to use any of the line types configured in your process:
Select the item in the layout.
Right-click and chooseto display the Cell Options dialog box.
Click the Layout tab and select a Line Type.
Clickto use the new line type in the layout.
See “Cell Options Dialog Box: Layout Tab ” for Cell Options dialog box Layout tab details.
See “The Layout Process File (LPF)” for more information on editing Layout Process Files (LPFs) and to learn about adding or editing line types.
 M.B. Bazdar, A.R. Djordjevic, R.F. Harrington, and T.K. Sarkar, "Evaluation of quasi-static matrix parameters for multiconductor transmission lines using Galerkin's method," IEEE Trans. Microwave Theory Tech., vol. MTT-42, July 1994, pp. 1223-1228
 M. Kirschning, R.H. Jansen, N.H.L. Koster, "Measurement and computer-aided modeling of microstrip discontinuities by an improved resonator method," IEEE MTT-S International Microwave Symposium Digest, 1983, pp. 495-497.